51单片机串行口中断服务程序
//串口中断服务程序,仅需做简单调用即可完成串口输入输出的处理 //编程:聂小猛。该资料来自“51单片机世界”http://go.163.com/~dz2000,欢迎访问。
//出入均设有缓冲区,大小可任意设置。 //可供使用的函数名: //char getbyte(void);从接收缓冲区取一个byte,如不想等待则在调用前检测inbufsign是否为1。
//getline(char idata *line, unsigned char n); 获取一行数据回车结束,已处理backspce和delete,必须定义最大输入字符数
//putinbuf(uchar c);模拟接收到一个数据 //putbyte(char c);放入一个字节到发送缓冲区 //putbytes(unsigned char
*outplace,j);放一串数据到发送缓冲区,自定义长度
//putstring(unsigned char code *puts);发送一个字符串到串口
//puthex(unsigned char c);发送一个字节的hex码,分成两个字节发。 //putchar(uchar c,uchar j);发送一个字节数据的asc码表达方式,需要定义小数点的位置
//putint(uint ui,uchar j);发送一个整型数据的asc码表达方式,需要定义小数点的位置 //CR;发送一个回车换行
//************************************************************************* #include //该头文件包括了51,52,80320的特殊寄存器,用在51,52上也可
#define uchar unsigned char #define uint unsigned int #define OLEN 64 /* size of serial transmission buffer */ idata unsigned char
outbuf[OLEN]; /* storage for transmission buffer */ unsigned char idata *outlast=outbuf; //最后由中断传输出去的字节位置
unsigned char idata *putlast=outbuf; //最后放入发送缓冲区的字节位置 #define ILEN 2 /* size of serial receiving buffer */
idata unsigned char inbuf[ILEN]; unsigned char idata *inlast=inbuf; //最后由中断进入接收缓冲区的字节位置 unsigned char
idata *getlast=inbuf; //最后取走的字节位置 bit outbufsign; //输出缓冲区非空标志 有=1 bit inbufsign; //接收缓冲区非空标志
有=1 bit inbufful; //输入缓冲区满标志 满=1 #define CR putstring("\r\n") //CR=回车换行
//***************************** //放入一个字节到发送缓冲区 putbyte(char c) {uchar i,j; ES=0; /*暂停串行中断,以免数据比较时出错?
*/ if (outlast==putlast ) { i=(0-TH1); do{i--;j=36; do {j--;}while(j!=0); }while(i!=0); //延时一个字节发送时间 } *putlast=c;
//放字节进入缓冲区 putlast++; //发送缓冲区指针加一 if (putlast==outbuf+OLEN) putlast=outbuf; //指针到了顶部换到底部
if (!outbufsign) {outbufsign=1;TI=1; } //缓冲区开始为空置为有,启动发送 ES=1; } //****************************** //放一串数据到发送缓冲区
putbytes(unsigned char *outplace,unsigned char j) { int i; for(i=0;i>4)&0x0f; putbyte(hex_[ch]); ch=c&0x0f; putbyte(hex_[ch]); } //************************************* //从接收缓冲区取一个byte,如不想等待则在调用前检测inbufsign是否为1。
uchar getbyte (void) { char idata c ; while (!inbufsign); //缓冲区空等待 ES=0; c= *getlast; //取数据 getlast++; //最后取走的数据位置加一
inbufful=0; //输入缓冲区的满标志清零 if (getlast==inbuf+ILEN) getlast=inbuf; //地址到顶部回到底部 if
(getlast==inlast) inbufsign=0; //地址相等置接收缓冲区空空标志,再取数前要检该标志 ES=1; return (c); //取回数据
} //***************************************** //接收一行数据,必须定义放数据串的指针位置和大小
del=0x7f,backspace=0x08,cr=0x0d,lf=0x0a void getline (uchar idata *line, unsigned char n) { unsigned char cnt = 0; //定义已接收的长度
char c; do { if ((c = getbyte ()) == 0x0d) c = 0x00; //读一个字节,如果是回车换成结束符 if (c == 0x08 || c == 0x7f)
//BACKSPACE 和 DEL 的处理 { if (cnt != 0) //已经输入退掉一个字符 {cnt--; //总数目减一 line--; //指针减一 putbyte
(0x08); //屏幕回显的处理 putbyte (' '); putbyte (0x08); } } else { putbyte (*line = c); //其他字符取入,回显 line++; //指针加一
cnt++; //总数目加一 } } while (cnt < n - 1 && c != 0x00 && c!=0x1b); //数目到了,回车或ESC停止 *line =
0; //再加上停止符0 } //**************************** //模拟接收到一个数据 putinbuf(uchar c) {ES=0; if(!inbufful) {*inlast=
c; //放入数据 inlast++; //最后放入的位置加一 if (inlast==inbuf+ILEN) inlast=inbuf;//地址到顶部回到底部 if
(inlast==getlast) inbufful=1; //接收缓冲区满置满标志 inbufsign=1; } ES=1; } //***************************************** //串口中断处理
serial () interrupt 4 { if (TI ) { TI = 0; if (outbufsign) //if (putlast==outlast) outbufsign=0; //else {SBUF=*outlast; //未发送完继续发送
outlast++; //最后传出去的字节位置加一 if (outlast==outbuf+OLEN) outlast=outbuf;//地址到顶部回到底部 if
(putlast==outlast) outbufsign=0; //数据发送完置发送缓冲区空标志 } } if (RI) { RI = 0; if(!inbufful) { *inlast= SBUF; //放入数据
inlast++; //最后放入的位置加一 inbufsign=1; if (inlast==inbuf+ILEN) inlast=inbuf;//地址到顶部回到底部 if
(inlast==getlast) inbufful=1; //接收缓冲区满置满标志 } } } //***************************** //串口初始化
0xfd=19200,0xfa=9600,0xf4=4800,0xe8=2400,0xd0=1200 serial_init () { SCON = 0x50; /* mode 1: 8-bit UART, enable receiver */ TMOD |= 0x20;
/* timer 1 mode 2: 8-Bit reload */ PCON |= 0x80; TH1 = 0xfd;//fa, //baud*2 /* reload value 19200 baud */ TR1 = 1; /* timer 1 run */ ES =
1; REN=1; EA=1; SM2=1; //SM2=1时收到的第9位为1才置位RI标志 //TMOD |=0x01; //th1 auto load 2X8,th0 1X16 //TH0=31; TL0=0; //X
32 =1S //TR0=1; ET0=1; } |
|